PeptiDex
Research Tool

Adipotide (FTPP) Reconstitution Calculator

A pro-apoptotic peptidomimetic referenced in adipose-tissue and metabolic research literature. This page works out concentration, volume per measured amount, syringe units and preparations per vial for a reconstituted Adipotide (FTPP) preparation, plus the mass-to-molar conversions for its stated molecular weight. Everything runs in your browser; nothing is transmitted or stored.

Also referenced as: FTPP, Fat-Targeted Proapoptotic Peptide

Pro-apoptotic peptidomimetic (prohibitin-targeting)MW ~2611 g/mol (approx. C152H252N44O42)
For research and educational purposes only. This is a unit-conversion tool for laboratory reference. It is not medical advice, not a dosing recommendation, and not an instruction for human use.

Inputs

Results

Concentration
2.5 mg/mL (2,500 mcg/mL)
Per syringe unit
25 mcg per unit
Volume per preparation
0.1 mL
Syringe units to draw
10 units
Preparations per vial
20 preparations

Worked example: a 5 mg vial reconstituted with 2 mL of bacteriostatic water. Change any input to recalculate.

A unit-conversion reference for laboratory work. Not a dosing recommendation and not an instruction for human use.

The pre-filled example, step by step

The inputs above are the neutral reference preparation this site uses everywhere the calculator appears: a 5 mg vial, 2 mL of bacteriostatic water, and a 250 mcg target amount. They are not a property of Adipotide (FTPP) and not an amount anyone should draw — they exist so the arithmetic is visible before you change anything.

  1. Concentration. 5 mg ÷ 2 mL = 2.5 mg/mL (2,500 mcg/mL), which for Adipotide (FTPP) is approximately 0.9575 mM at its stated molecular weight.
  2. Per syringe unit. A U-100 syringe divides 1 mL into 100 units, so one unit holds 2,500 mcg ÷ 100 = 25 mcg.
  3. Volume for the 250 mcg target. 250 mcg ÷ 2,500 mcg/mL = 0.1 mL, or 10 units on that syringe.
  4. Preparations per vial. 5,000 mcg ÷ 250 mcg = 20 preparations.

Arithmetic on a laboratory preparation, shown as a unit-conversion reference. Not medical advice, not a dosing recommendation, not an instruction for human use. The full derivation, and why the diluent volume is a choice rather than a constant, is on the main reconstitution calculator.

Mass and molar equivalents for Adipotide (FTPP)

Derived from the molecular weight recorded on the Adipotide (FTPP) entry: ~2611 g/mol (approx. C152H252N44O42) — the entry states this as an approximate figure, so the equivalents below are approximate too. Concentration in molar units is what an in-vitro protocol is usually specified in.

Mass to molar conversions for Adipotide (FTPP) at its stated molecular weight.
QuantityMolar equivalent
1 mg of Adipotide (FTPP)383 nmol (0.383 µmol)
1 mcg of Adipotide (FTPP)0.383 nmol
A 1 mg/mL solution0.383 mM (383 µM)

Molar amount = mass ÷ molecular weight. Figures are shown to four significant digits and are a unit conversion, not a measurement.

Reconstitution recorded for Adipotide (FTPP)

Lyophilized; typically reconstituted with sterile or bacteriostatic water

Quoted from the Adipotide (FTPP) entry. Amounts reported in the research literature for this compound are documented on that entry, under the disclaimer they belong with — they are not reproduced next to a calculator. Read the full Adipotide (FTPP) entry.

Handling questions for Adipotide (FTPP)

How is adipotide handled for research?

Adipotide is supplied as a lyophilized powder and reconstituted with sterile/bacteriostatic water for laboratory use. It is stored refrigerated or frozen as a solid and kept refrigerated once reconstituted. A COA with HPLC purity and mass identity is standard. It is a research compound with no approved therapeutic status.

Answers are published on the Adipotide (FTPP) entry. Educational summaries of research-literature context, not medical advice.

Continue exploring